Water Safe Testing Kit

What Does the Water Safe Testing Kit Do?

This Watersafe® test kit contains everything you will need to find out simply and accurately if your water contains unsafe or undesirable levels of one or more of 8 common contaminants.

Water Test Desired Value

EPA maximum contaminant levels or guildline standards

Before you begin

1. Keep tests out of reach of children and pets. Do not ingest anything from this test kit. Do not drink water sample used for testing. Store and use at room temperature (60-86 F)
2. Do not open packets or a vial until you are ready to perform the tests.
3. Do not use on hot water or water containing bleach detergents.
4. Do not re-use any part of the test kit.
5. Read and follow all instructions carefully.

Water Testing Instructions

Bacteria Test Instructions

1. Take out the bacteria Test vial and set upright on a flat surface.
2. Collect water sample or turn on tap to a very slow stream.
3. Carefully twist off cap and fill vial to 1/2 inch below the top (to 5 ml line). DO NOT OVERFILL and DO NOT SPILL the bacterial growth powder in the vial.
4. Replace cap and twist on tightly. Shake the vial vigorously for 20 seconds.
5. Place the capped vial upright in a warm area (70-90 F) where it cannot be disturbed for 48 hrs.
6. After 48 hrs., observe the color of the liquid without opening the vial.

   	Purple Color: Negative Result (No bacteria were detected)
   	Yellow Color: Positive Result (It is highly likely that potentially harmful bacteria were detected.

7. For positive results, add bleach to the sample before pouring down the toilet, then wash hands carefully. Negative samples may be poured directly into the toilet. Discard vial in the trash.

Lead / Pesticide Test Instructions

The Watersafe® Lead Test can detect dissolved lead at levels at below the EPA Action level of 15 parts per billion (ppb). The Watersafe® Pesticide Test detects two of the most common pesticides used in the US at or below the EPA Maximum Contaminant Level (altrazine-3 ppb, and simazine- 4ppb).

1. Open Lead / Pesticide packet and take out contents. The packet contains a test vial, a dropper pipette, two Watersafe® test strips, and a desiccant (to be discarded).
2. Using dropper, Place water sample into test vial. To pick up the sample, tightly squeeze the bulb at the end of the dropper and place the open end into the water sample. Release the bulb to pick up the sample, then squeeze again to expel the sample into the vial. Use only ONE dropper full of water!
3. Swirl vial gently for several seconds. Place on a flat surface
4. Place both test strips into the test vial, with arrows pointing DOWN.
5. Wait 10 minutes. DO not disturb strips or vial during this time. Blue lines will appear on the strips.
6. Take the strips out of the vial and read results.

   Negative: Bottom line(next to number 1) is darker then the top line (next to number 2) If you only see one line next to number 1, the test is negative.

   If you only see one line next to number 1, the test is negative.
   

   Positive: Top line (next to number 2) is darker then bottom line(next to number 1), or lines are equally dark.
   

7. Note: If no lines appear, or both lines are very light, the test did not run properly and the result is not valid. If a test strip shows a positive result, your water sample may contain lead or pesticides at a toxic level.

Nitrate / Nitrite Test Instructions

1. Carefully open Nitrate / Nitrite Test packet and take out test strip
2. Immerse the regent pads into water sample for 2 seconds, remove, after one minute match colors with the chart below.
3. Colors are stable for 1 minute.

   Total Nitrate/Nitrite (end pad)

   0	0.5	2.0	5.0	10	20	50	ppm

   Nitrite (pad nearest handle)
   

   0	0.15	0.3	1.0	1.5	3.0	10	ppm

Ph | Hardness | Chlorine Test Instructions

1. Carefully open pH/ Hardness/ Chlorine Test packet and take out test strip.
2. Immerse the regent pads into the water sample and remove immediately. Hold the strip level for 15 seconds.
3. Match pH, Hardness and Total Chlorine Pads (in that order) to the color chart below.

   pH (end pad)

   6.0	6.5	7.5	8.5	10	ppm

   LR Total Hardness (middle pad)
   

   0	50	120	250	425	ppm

   Total Chlorine (pad nearest handle)
   

   0	2.0	4.0	10	ppm

Back to Top